2026.11.18

SSD Destruction in Bangkok: Why Solid-State Drives Need Different Handling Than Hard Disks

Why SSDs need different handling than hard disks: wear levelling and spare area, why degaussing does nothing, sanitize first, particle size for destruction, hidden M.2 and soldered storage, and a certificate checklist.

อ่านภาษาไทย

If you are looking for an SSD destruction service in Bangkok, you have probably noticed that most of the advice online was written for spinning hard disks. Solid-state drives store data in a completely different way, and several habits that work on an old hard disk, such as degaussing, overwriting the whole drive or punching a single hole through it, do far less on an SSD than people assume. This guide explains why SSDs need different handling, what "destroyed" should mean for flash storage, where SSDs hide in a typical Thai office, and what your certificate should record when the drives are gone.

Why an SSD Is Not Just a Faster Hard Disk

A hard disk writes data onto magnetic platters, and when you overwrite a sector, the new data lands in the same physical place as the old. An SSD does not work like that. Its data sits in NAND flash chips, and a controller inside the drive constantly decides where each piece of data physically lives. To spread wear evenly, it writes new data to fresh cells and quietly retires old ones. Most SSDs also keep a reserve of spare capacity, often called over-provisioning, that the computer cannot see or address directly.

The practical result is that your operating system only ever sees a map of the drive, not the drive itself. When software "overwrites every sector", the controller may simply write the new pattern somewhere else and leave older copies sitting in retired or spare blocks. The US National Institute of Standards and Technology makes this point in its media sanitization guideline, NIST SP 800-88 Revision 2 (September 2025): for SSDs with over-provisioning, repeated overwrite passes achieve very little confidentiality protection. That is why the free wiping tools many IT teams have used for years are a poor fit for modern laptops and servers.

Degaussing Does Nothing to Flash Storage

Degaussing scrambles magnetic media with a powerful magnetic field. It can be effective on hard disks and tapes, but SSDs, USB sticks, memory cards and phone storage are not magnetic, so a degausser leaves their data untouched. NIST's guideline says plainly that degaussing should not be used for flash storage such as SSDs. If a vendor proposes to "degauss everything" in a batch that includes laptops bought in the last few years, the SSDs in that batch have not been sanitized at all. We compared shredding, crushing and degaussing in more detail in our guide to choosing a hard drive destruction service in Bangkok; the short version is that SSDs need a method that reaches the chips themselves.

Step One for Working SSDs: Sanitize Before They Leave Your Hands

If an SSD still works, the strongest first step is not physical at all. Modern SATA and NVMe drives include built-in sanitize commands, designed by the drive makers, that act on every cell the controller manages, including the hidden spare area that ordinary software cannot reach. The fastest of these is cryptographic erase: on a drive that encrypts everything it stores, destroying the internal key makes the remaining data unreadable in seconds. NIST describes cryptographic erase as a purge technique that can sanitize with high assurance, but only when its conditions are met, which in practice means the drive's encryption was genuinely active and the tool you used reported success.

A few points matter in practice:

  • Use the drive maker's utility or a recognised sanitize tool, not a file shredder or a quick format. Record the tool name, the result and the drive serial number.
  • Do not assume encryption. If you cannot confirm that BitLocker, FileVault or the drive's own encryption was on from day one, treat the drive as unencrypted.
  • A sanitize that fails or cannot be verified is a reason to destroy, not a reason to try a weaker method.

For drives holding customer, payroll, medical or financial data, many companies do both: sanitize the working drives in-house, then send them for physical destruction anyway. That layered approach costs very little extra and covers you if one step turns out weaker than expected. For laptops, where this step is often skipped, see our article on whether a factory reset is enough for company laptops.

SSD Destruction and Particle Size: Why "Shredded" Can Mean Very Different Things

When an SSD is dead, locked, encrypted with a lost key, or simply too sensitive to reuse, physical destruction is what remains. Here the detail that matters is the size of the pieces. A single flash chip is only a few square centimetres, yet it can hold a very large amount of data. A hard drive shredder that tears platters into strips several centimetres wide can pass a small SSD or M.2 stick through with chips cracked but not broken, and a crushed SSD can leave intact chips on a bent board.

The international standard for destroying data carriers, ISO/IEC 21964 (originally the German DIN 66399), sets separate security levels for electronic media such as SSDs, USB sticks and phones. Level E-3 requires pieces of no more than 160 mm², E-4 requires the chips themselves to be split into pieces of no more than 30 mm², and E-5 requires the chips to be broken several times into pieces of no more than 10 mm². At the strictest end, the US National Security Agency's requirements for solid-state disintegrators call for particles with a maximum edge of 2 mm.

NIST's 2025 revision goes further still: because data density keeps rising, it says shredding and pulverizing should be avoided for anything but the lowest security categories of data, and points to melting or incineration for the highest. Most Thai companies are not handling state secrets, and for ordinary business data a combination of a proper sanitize step and physical destruction of the chips is a sensible, defensible standard. The useful question to ask any vendor, including us, is simple: what happens to the flash chips, and what does the certificate record?

Where SSDs Hide in a Bangkok Office

SSD destruction is not only about the obvious 2.5-inch drives in a box. When you plan a clear-out, look for flash storage in all of these places:

  • M.2 and NVMe sticks inside laptops, desktops and mini PCs, often no bigger than a stick of chewing gum and easy to miss in a parts bin.
  • Soldered storage in many recent thin laptops and tablets, including Apple silicon MacBooks. The storage cannot be removed, so the choices are a verified built-in erase or destroying the board that carries the chips. Mention these machines when you book so the method is agreed in advance.
  • Servers and storage arrays, which may hold enterprise SSDs in hot-swap bays plus small boot drives on the motherboard. Our server data destruction service covers decommissioned servers.
  • NAS boxes with SSD cache drives, which can hold fragments of recently used files even after the main hard disks are pulled.
  • External SSDs and USB sticks handed out to staff, which rarely appear in any asset register.

Laptops are usually the largest single source. If you would rather send whole machines than pull the drives yourself, our laptop data destruction service handles the storage and leaves the laptop itself intact for donation or recycling.

What an SSD Destruction Certificate Should Record

A certificate is your evidence under Thailand's PDPA, which expects a data controller to have a working system for erasing or destroying personal data it no longer needs. For SSDs, check that each entry records:

  • The serial number of the drive itself, plus the asset tag or serial of the laptop, desktop or server it came from, so an auditor can trace one to the other.
  • The media type: SATA SSD, M.2/NVMe, soldered storage, USB flash, and so on.
  • The method used, and whether a sanitize step was performed before destruction.
  • The date, and who carried out or witnessed the work.

NIST's guideline suggests an even fuller record, including manufacturer, model, the tool used and how the result was verified. You do not need every field for every job, but the serial number, method and date are the minimum that makes a certificate worth keeping.

A Practical SSD Retirement Workflow

  1. Inventory first. List every drive by serial number and the device it came from before anything leaves the building.
  2. Separate by condition. Working drives go to the sanitize queue; dead, locked or unknown-key drives go straight to destruction.
  3. Sanitize working drives with a proper tool and log the result per serial.
  4. Decide on reuse or destruction. Reuse only drives that sanitized successfully and hold low-risk data; destroy the rest.
  5. Hand over under control, in sealed packaging with a signed handover list.
  6. Match the certificate to your inventory and file it with your PDPA records. For a wider refresh that also covers monitors, docks and cabling, fold the drives into a single IT asset disposal project.

What This Means for You

An SSD is not a smaller hard disk, so it should not be retired like one. Overwriting tools and degaussers that served you well on spinning disks leave flash storage largely untouched, and a rough crush or coarse shred can leave readable chips behind. Sanitize working drives with a proper tool, make sure physical destruction actually breaks the chips, find the M.2 sticks and soldered storage before they slip out with the e-waste, and keep a certificate that names every drive by serial number.

Ready to retire a batch of SSDs? Our hard drive and SSD destruction service physically destroys SATA SSDs, M.2 and NVMe drives and hard disks, and issues a Certificate of Destruction for every drive with its serial number, method and date. Ship drives to us from anywhere in Thailand or request a pickup in Bangkok, with office collection available for corporate jobs of 50 devices or more. Get an instant quote or call 082-797-3702.

Related Articles

Hard Drive and SSD Destruction Service Bangkok

Certified, PDPA-compliant destruction in Bangkok.

Learn More